Vietnam liquid ring vacuum pump

2SK type Vietnam liquid ring vacuum pump selection

2SK type liquid ring vacuum pump working principle

The working process of 2SK type liquid ring vacuum pump, compressor and gas-water separator is as follows: the gas enters the vacuum pump or compressor through the pipeline through the valve, and then is discharged into the gas-water separator through the gas-water separator exhaust pipe.
When 2SK type liquid ring vacuum pump as the compressor, the compressor discharge air water mixture in gas water separator after the separation, gas through the valve to the need of compressed gas system, and the water in gas water separator, for the water level maintain gets water separator is equipped with automatic water switch, when the water level is higher than the required water level, water switch, water overflow from the overflow pipe, when the water level below the required level, overflow water switch is closed, rising water levels in the gas water separator, to achieve the required level. The working water in a vacuum pump or compressor is supplied by a gas-water separator (tap water is also available) and the amount of water supplied is adjusted by the valve on the supply pipe.

2SK type liquid ring vacuum pump steam separator of installation

1. The gas-water separator is installed on the foundation according to the outline drawing.
2. If it is necessary to change the installation position, please pay attention that the connection line between the separator and the pump shall not be too long and the turn shall not be too sharp. Otherwise, the flow loss of air-water mixture in the pipeline will increase, which will increase the exhaust resistance, reduce the flow rate and vacuum degree, and increase the power consumption.
3. The inlet flange of the gas-water separator and the pump exhaust flange are connected by elbow pipe.

2SK type liquid ring vacuum pump installation instructions

The exhaust pipe of 2SK type liquid ring vacuum pump or compressor is connected with the inlet pipe of air and water separator. When used as a compressor, the exhaust pipe of air and water separator is connected with the system using compressed gas. In general, the pipeline shall not be too long and the turn shall not be too urgent. When used as 2SK type liquid ring vacuum pump, the gas is discharged to the atmosphere from the exhaust port of the water-air separator. To improve the working environment, the gas may be piped out of the workplace.
A gate valve shall be installed on the inlet pipe of type 2SK liquid ring vacuum pump or compressor to prevent the water in type 2SK liquid ring vacuum pump or compressor from returning to the system under the pressure of exhaust pipe. In order to facilitate the work, it is best to install a vacuum meter between the inlet and the valve, so as to check the 2SK type liquid ring vacuum pump at any time whether the working condition is normal. When used as compressor and gate valves should be installed on the exhaust pipe of the gas water separator, (it is best to check valve to ensure the abnormal situation occurs, not make the gas return, as to make the work of water return system), to install a pressure gauge between the exhaust pipe and valve, may at any time check pressure feed gas to reach the required pressure.
2SK type liquid ring vacuum pump or compressor inlet should be installed before the filter, to prevent particles from entering the pump.

2SK liquid ring vacuum pump of instructions for type selection

1. please provide the following detailed data:
(1) 2SK liquid ring vacuum pump product name and model
(2) the vacuum degree of 2SK liquid ring vacuum pump requires units of PA or MPA
(3) 2SK type liquid ring vacuum pump pumping speed requirements unit L/S or M3/MIN
(4) 2SK type liquid ring vacuum pump use or not and working conditions
(5) 2SK type liquid ring vacuum pump motor power (KW)
(6) 2SK type liquid ring vacuum pump speed (r/min)
(7) 2SK type liquid ring vacuum pump voltage [V]
(8) 2SK type liquid ring vacuum pump import and export caliber
(9) 2SK liquid ring vacuum pump material requirements
Is there any attachment on the 2SK type liquid ring vacuum pump, so that we will correctly select the model for you.
2. If the design unit has selected the 2SK type liquid ring vacuum pump model of our company, please order directly from the sales department of the company according to the 2SK type liquid ring vacuum pump model.
3. When the occasion is very important or the environment is complex, please try your best to provide design drawings and detailed parameters, and our technical experts will confirm the type selection for you.