My company’s production of rotary vane vacuum pump effectively prevent oil return to happen

Posted on Fri, 18 May 2018 09:15:35 +0000

When stop rotary vane vacuum pumps, oil hole and pump chamber are inter linked or surface of exhaust valve, shaft seal, pump cover, air inlet pipe, air valve, such as untight seal, as a result of the existence of liquid level difference and gravity are in a vacuum tank and pump cavity and differe...

+ Continue reading

Water pump maintenance

Posted on Fri, 18 May 2018 08:41:34 +0000

Firstly, The power supply should be inspected: the connection whether firm; the switch contact whether dense; the fuse whether blown; the three-phase power supply whether equal or not. If there is a broken circuit, poor contact, blown fuse, or lack of phase, the cause should be ascertained and re...

+ Continue reading

Damage Analysis Factors of Dry Screw Vacuum Pumps

Posted on Fri, 18 May 2018 08:26:41 +0000

I.Analysis on Corrosive rotor surface Vacuum pump feed medium containing sulfur dioxide, water, sulfur dioxide combined with water to generate sulfurous acid, sulfurous acid on the metal corrosive effect, in order to prevent rotor, pump chamber corrosion, the surface of the rotor and pump Teflon ...

+ Continue reading

Obtain Ultra-high vacuum method by oil diffusion pump

Posted on Fri, 18 May 2018 08:24:52 +0000

Oil diffusion pump is often used in high-vacuum pumping system by  taking some technical measures, you can get ultra-high vacuum and  the method is: 1. choose a good performance diffusion pump oil Pump oil has a great influence on the ultimate pressure of the oil diffusion pump. Such as the use o...

+ Continue reading

Single-end mechanical seal flushing program

Posted on Fri, 18 May 2018 08:22:50 +0000

PLAN 01 (Single-sided self-rinse) Description: The internal circulation from the outlet of the pump to the seal. Its operation similar to PLAN11. Reason: sealed chamber cooling; sealed chamber exhaust. Application: Single-end seals more be used for clean the transported fluid of viscous and easy ...

+ Continue reading

Possible Questions and Solutions of 2XZ-C Rotary Vane Vacuum Pump

Posted on Fri, 18 May 2018 08:16:16 +0000

2XZ-C series of double-stage rotary vane vacuum pump is developed over years reaches by our special engineer team. The working process of 2XZ-C is: Rotor drives vanes to work in the surface of inside chamber, separate the inlet and outlet port and then drive gas out to create vacuum. 2XZ-C rotary...

+ Continue reading

Analysis of Main Causes that Oil Return of Diffusion Pump

Posted on Fri, 18 May 2018 08:00:15 +0000

Oil return is the biggest weakness of the oil diffusion pump, The return oil just only can be reduced and can’t be eradicated. In order to reduce the diffusion pump oil return, Finding out the main source and reason of oil return is necessary. Then thinking how to reduce the oil return rate. Part...

+ Continue reading

The bearing lubrication and troubleshooting of water ring vacuum pump

Posted on Fri, 18 May 2018 07:47:05 +0000

1. Lubricating the bearings Grease type , operating conditions Lubrication intervals of 4000 hours of operation each applyunder normal operating conditions and at ambient temperatures up to 40 ℃。 The regreasing intervals apply to normal loads, low-vibration running, approximately neutral ambient...

+ Continue reading

Notes and Possible Problems of Roots Vacuum Pump

Posted on Fri, 18 May 2018 07:40:19 +0000

1.Simple introduction of Roots Vacuum Pump Roots vacuum pump, also known as mechanical booster pump, uses two eight-shaped rotor in the pump casing for synchronous rotation, so as to complete the process of inhalation and exhaust. Since main parts such as the pump casing, rotor and the end cap in...

+ Continue reading

Vacuum Pump Maintenance

Posted on Fri, 18 May 2018 06:56:22 +0000

1. Check the vacuum pump piping and the junction if have any loose phenomenon. 2. Adding bearing lubricating oil to the bearing body, oil level should be observed in the oil center line, the oil should be replaced or added timely. 3. Unscrew the pump body’s  water diversion plug and pour into wat...

+ Continue reading